Reinforcement ColumnRebars/pt-br

Armadura circular de vergalhão

Reforço de pilares com duas braçadeiras e seis barras

Arch

Descrição

The Reinforcement ColumnRebars tool allows the user to create reinforcing bars inside a Column Arch Structure object.

This tool is part of the Reinforcement Workbench, an external workbench that can be installed with the Addon Manager.

Three usage examples are available:

• Single tie rectangular column (see below)
• Two ties six rebars rectangular column
• Circular column

Single tie reinforcement inside a column

Utilização

1. Select any face of a previously created Arch Structure object.

2. Then select Column Reinforcement from the rebar tools.

3. A dialog box will pop-out on screen as shown below.

Dialog Box for the Arch Rebar ColumnReinforcement tool

4. Select the desired type of column reinforcement.

5. Give inputs for data related to ties.

6. Click Next and the dialog box will be updated as shown below.

Dialog Box for Main Rebars data

7. Select desired rebar type and fill data for main rebars.

8. Click Next and the dialog box will be updated as shown below.

Dialog Box for XDirection Rebars data

9. Select desired rebar type and fill data for xdirection rebars.

10. Click Next and the dialog box will be updated as shown below.

Dialog Box for YDirection Rebars data

11. Select desired rebar type and fill data for ydirection rebars.

12. Click OK or Apply to generate column reinforcement.

13. Click Cancel to exit the dialog box.

Propriedades

Ties:

• DadosLeft Cover: The distance between the left end of the tie to the left face of the structure.
• DadosRight Cover: The distance between the right end of the tie to right face of the structure.
• DadosTop Cover: The distance between tie from the top face of the structure.
• DadosBottom Cover: The distance between tie from the bottom face of the structure.
• DadosOffset: The distance between tie from the top/bottom face of the structure.
• DadosDiameter: Diameter of the tie.
• DadosBent Angle: Bent angle defines the angle at the ends of a tie.
• DadosExtension Factor: Extension Factor defines length of end of tie, expressed in times the diameter.
• DadosNumber: The number of ties.
• DadosSpacing: The distance between the axes of each tie.

Main Rebars: Rebars present at corners of tie

• DadosRebar Type: Type of main rebars.
• DadosHook Orientation: Orientation of LShaped hooks.
• DadosHook Extend Along: Direction for hook extension.
• DadosHook Extension: Length of hook of LShape rebars.
• DadosRounding: A rounding value to be applied to the corners of the LShape rebars, expressed in times the diameter.
• DadosTop Offset: The distance between rebar from the top face of the structure.
• DadosBottom Offset: The distance between rebar from the bottom face of the structure.
• DadosDiameter: Diameter of the main rebars.

XDir Secondary Rebars: Rebars along x-direction except main rebars

• DadosRebar Type: Type of x-direction rebars.
• DadosHook Orientation: Orientation of LShaped hooks.
• DadosHook Extension: Length of hook of LShape rebars.
• DadosRounding: A rounding value to be applied to the corners of the LShape rebars, expressed in times the diameter.
• DadosTop Offset: The distance between rebar from the top face of the structure.
• DadosBottom Offset: The distance between rebar from the bottom face of the structure.
• DadosNumber#Diameter: Number#Diameter set of the x-direction rebars.

YDir Secondary Rebars: Rebars along y-direction except main rebars

• DadosRebar Type: Type of y-direction rebars.
• DadosHook Orientation: Orientation of LShaped hooks.
• DadosHook Extension: Length of hook of LShape rebars.
• DadosRounding: A rounding value to be applied to the corners of the LShape rebars, expressed in times the diameter.
• DadosTop Offset: The distance between rebar from the top face of the structure.
• DadosBottom Offset: The distance between rebar from the bottom face of the structure.
• DadosNumber#Diameter: Number#Diameter set of the y-direction rebars.

Scripting

See also: Arch API, Reinforcement API and FreeCAD Scripting Basics.

The Reinforcement ColumnRebars tool can be used in macros and from the Python console by using the following function:

Create Single Tie Four Rebars

RebarGroup = makeSingleTieFourRebars(
    l_cover_of_tie,
    r_cover_of_tie,
    t_cover_of_tie,
    b_cover_of_tie,
    offset_of_tie,
    bent_angle,
    extension_factor,
    dia_of_tie,
    number_spacing_check,
    number_spacing_value,
    dia_of_rebars,
    t_offset_of_rebars,
    b_offset_of_rebars,
    rebar_type="StraightRebar",
    hook_orientation="Top Inside",
    hook_extend_along="x-axis",
    l_rebar_rounding=None,
    hook_extension=None,
    structure=None,
    facename=None,
).rebar_group

• Creates a RebarGroup object from the given structure, which is an Arch Structure, and facename, which is a face of that structure.
  • If no structure nor facename are given, it will take the user selected face as input.
• l_cover_of_tie, r_cover_of_tie, t_cover_of_tie, b_cover_of_tie and offset_of_tie are inner offset distances for the tie elements with respect to the faces of the structure. They are respectively the left, right, top, bottom and front/rear offsets.
• bent_angle define the angle of the tip of the reinforcement loop.
• extension_factor define the length of the tip of the reinforcement loop, expressed in times the diameter.
• dia_of_tie is the diameter of the ties.
• number_spacing_check if it is True it will create as many ties as given by number_spacing_value; if it is False it will create ties separated by the numerical value of number_spacing_value.
• number_spacing_value specifies the number of ties, or the value of the separation between them, depending on number_spacing_check.
• dia_of_rebars is the diameter of the main rebars.
• t_offset_of_rebars and b_offset_of_rebars are inner offset distances for the main rebars with respect to the top and bottom faces of the structure, respectively.
• rebar_type is the type of the main rebars; it can be "StraightRebar" or "LShapeRebar".
• hook_orientation specifies the orientation of LShaped hook; it can be: "Top Inside", "Top Outside", "Bottom Inside", "Bottom Outside", "Top Right", "Top Left", "Bottom Right" or "Bottom Left".
• hook_extend_along specifies direction for hook extension; it can be "x-axis" or "y-axis".
• l_rebar_rounding is the parameter that determines the bending radius of the LShaped main rebars, expressed as times the diameter.
• hook_extension is the length of hook of LShaped rebars.

Exemplo

import FreeCAD, Draft, Arch
from ColumnReinforcement import SingleTie

# It doesn't work if the structure is not based on a face.
# Structure = Arch.makeStructure(length=1000, width=400, height=400)

Rect = Draft.makeRectangle(400, 400)
Structure = Arch.makeStructure(Rect, height=1600)
Structure.ViewObject.Transparency = 80
FreeCAD.ActiveDocument.recompute()

# For Straight Rebars

RebarGroup = SingleTie.makeSingleTieFourRebars(
    l_cover_of_tie=40,        
    r_cover_of_tie=40,
    t_cover_of_tie=40,
    b_cover_of_tie=40,
    offset_of_tie=100,
    bent_angle=135,
    extension_factor=2,
    dia_of_tie=8,
    number_spacing_check=True,
    number_spacing_value=10,
    dia_of_rebars=16,
    t_offset_of_rebars=40,
    b_offset_of_rebars=40,
    rebar_type="StraightRebar",
    hook_orientation="Top Inside",
    hook_extend_along="x-axis",
    l_rebar_rounding=None,
    hook_extension=None,
    structure=Structure,
    facename="Face6",
).rebar_group

# For LShaped Rebars with hook along x-axis

RebarGroup = SingleTie.makeSingleTieFourRebars(
    l_cover_of_tie=40,        
    r_cover_of_tie=40,
    t_cover_of_tie=40,
    b_cover_of_tie=40,
    offset_of_tie=100,
    bent_angle=135,
    extension_factor=2,
    dia_of_tie=8,
    number_spacing_check=True,
    number_spacing_value=10,
    dia_of_rebars=16,
    t_offset_of_rebars=-40,
    b_offset_of_rebars=-40,
    rebar_type="LShapeRebar",
    hook_orientation="Top Outside",
    hook_extend_along="x-axis",
    l_rebar_rounding=2,
    hook_extension=40,
    structure=Structure,
    facename="Face6",
).rebar_group

# For LShaped Rebars with hook along y-axis

RebarGroup = SingleTie.makeSingleTieFourRebars(
    l_cover_of_tie=40,        
    r_cover_of_tie=40,
    t_cover_of_tie=40,
    b_cover_of_tie=40,
    offset_of_tie=100,
    bent_angle=135,
    extension_factor=2,
    dia_of_tie=8,
    number_spacing_check=True,
    number_spacing_value=10,
    dia_of_rebars=16,
    t_offset_of_rebars=-40,
    b_offset_of_rebars=-40,
    rebar_type="LShapeRebar",
    hook_orientation="Top Outside",
    hook_extend_along="y-axis",
    l_rebar_rounding=2,
    hook_extension=40,
    structure=Structure,
    facename="Face6",
).rebar_group

Create Single Tie Multiple Rebars

RebarGroup = makeSingleTieMultipleRebars(
    l_cover_of_tie,
    r_cover_of_tie,
    t_cover_of_tie,           
    b_cover_of_tie,                      
    offset_of_tie,                       
    bent_angle,                          
    extension_factor,
    dia_of_tie,     
    number_spacing_check,
    number_spacing_value,
    dia_of_main_rebars,
    main_rebars_t_offset,
    main_rebars_b_offset,
    main_rebars_type="StraightRebar",
    main_hook_orientation="Top Inside",
    main_hook_extend_along="x-axis",
    l_main_rebar_rounding=None,
    main_hook_extension=None,
    sec_rebars_t_offset=None,
    sec_rebars_b_offset=None,
    sec_rebars_number_diameter=None,
    sec_rebars_type=("StraightRebar", "StraightRebar"),
    sec_hook_orientation=("Top Inside", "Top Inside"),
    l_sec_rebar_rounding=None,
    sec_hook_extension=None,
    structure=None,
    facename=None,
)

• Creates a RebarGroup object from the given structure, which is an Arch Structure, and facename, which is a face of that structure.
  • If no structure nor facename are given, it will take the user selected face as input.
• l_cover_of_tie, r_cover_of_tie, t_cover_of_tie, b_cover_of_tie and offset_of_tie are inner offset distances for the tie elements with respect to the faces of the structure. They are respectively the left, right, top, bottom and front/rear offsets.
• bent_angle define the angle of the tip of the reinforcement loop.
• extension_factor define the length of the tip of the reinforcement loop, expressed in times the diameter.
• dia_of_tie is the diameter of the ties.
• number_spacing_check if it is True it will create as many ties as given by number_spacing_value; if it is False it will create ties separated by the numerical value of number_spacing_value.
• number_spacing_value specifies the number of ties, or the value of the separation between them, depending on number_spacing_check.
• dia_of_main_rebars is the diameter of the main rebars.
• main_rebars_t_offset and main_rebars_b_offset are inner offset distances for the main rebars with respect to the top and bottom faces of the structure, respectively.
• main_rebars_type is the type of the main rebars; it can be "StraightRebar" or "LShapeRebar".
• main_hook_orientation specifies the orientation of main LShaped hook; it can be: "Top Inside", "Top Outside", "Bottom Inside", "Bottom Outside", "Top Right", "Top Left", "Bottom Right" or "Bottom Left".
• main_hook_extend_along specifies direction for main hook extension; it can be "x-axis" or "y-axis".
• l_main_rebar_rounding is the parameter that determines the bending radius of the LShaped main rebars, expressed as times the diameter.
• main_hook_extension is the length of hook of main LShaped rebars.
• sec_rebars_t_offset and sec_rebars_b_offset are tuples (xdir_rebars_t_offset, ydir_rebars_t_offset) and (xdir_rebars_b_offset, ydir_rebars_b_offset) respectively, that defines inner offset distances for the secondary x-direction and y-direction rebars with respect to the top and bottom faces of the structure, respectively.
• sec_rebars_number_diameter is a tuple (xdir_rebars_number_diameter, ydir_rebars_number_diameter) that defines number#diameter set of the secondary x-direction and y-direction rebars, respectively.
• sec_rebars_type is a tuple (xdir_rebars_type, ydir_rebars_type) that defines the type of secondary x-direction and y-direction rebars ,respectively; it can have "StraightRebar" or "LShapeRebar" as rebar type.
• sec_hook_orientation is a tuple (xdir_hook_orientation, ydir_hook_orientation) that defines the orientation of secondary x-direction and y-direction LShaped hook; it can have "Top Inside", "Top Outside", "Bottom Inside", "Bottom Outside", "Top Right", "Top Left", "Bottom Right" or "Bottom Left" as hook_orientation.
• l_sec_rebar_rounding is a tuple (l_xdir_rebar_rounding, l_ydir_rebar_rounding) that determines the bending radius of the LShaped secondary x-direction and y-direction LShaped rebars, expressed as times the diameter of x-direction and y-direction LShaped rebars, respectively.
• sec_hook_extension is a tuple (xdir_hook_extension, ydir_hook_extension) that defines the length of hook of secondary x-direction and y-direction LShaped rebars.

Exemplo

import FreeCAD, Draft, Arch
from ColumnReinforcement import SingleTieMultipleRebars

# It doesn't work if the structure is not based on a face
# Structure = Arch.makeStructure(length=1000, width=400, height=400)

Rect = Draft.makeRectangle(400, 400)
Structure = Arch.makeStructure(Rect, height=1600)
Structure.ViewObject.Transparency = 80
FreeCAD.ActiveDocument.recompute()

RebarGroup = SingleTieMultipleRebars.makeSingleTieMultipleRebars(
    l_cover_of_tie=40,        
    r_cover_of_tie=40,
    t_cover_of_tie=40,
    b_cover_of_tie=40,
    offset_of_tie=100,
    bent_angle=135,
    extension_factor=2,
    dia_of_tie=8,
    number_spacing_check=True,
    number_spacing_value=10,
    dia_of_main_rebars=16,
    main_rebars_t_offset=-40,
    main_rebars_b_offset=-40,
    main_rebars_type="LShapeRebar",
    main_hook_orientation="Top Outside",
    main_hook_extend_along="x-axis",
    l_main_rebar_rounding=2,
    main_hook_extension=40,
    sec_rebars_t_offset=(-40, -40),
    sec_rebars_b_offset=(-40, -40),
    sec_rebars_number_diameter=("2#20mm+1#16mm+2#20mm", "1#20mm+1#16mm+1#20mm"),
    sec_rebars_type=("LShapeRebar", "LShapeRebar"),
    sec_hook_orientation=("Top Outside", "Top Outside"),
    l_sec_rebar_rounding=(2, 2),
    sec_hook_extension=(40, 40),
    structure=Structure,
    facename="Face6",
)

Edition of Single Tie Four Rebars

You can change the properties of the ties and rebars with the following function:

rebar_group = editSingleTieFourRebars(
    rebar_group,
    l_cover_of_tie,
    r_cover_of_tie,    
    t_cover_of_tie,           
    b_cover_of_tie,
    offset_of_tie,
    bent_angle,
    extension_factor,
    dia_of_tie,
    number_spacing_check,
    number_spacing_value,
    dia_of_rebars,
    t_offset_of_rebars,
    b_offset_of_rebars,
    rebar_type="StraightRebar",
    hook_orientation="Top Inside",
    hook_extend_along="x-axis",
    l_rebar_rounding=None,
    hook_extension=None,
    structure=None,
    facename=None,
)

• rebar_group is a previously created ColumnReinforcement group object.
• The other parameters are the same as required by the makeSingleTieFourRebars() function.
• structure and facename may be omitted so that the rebar stays in the original structure.

Exemplo

from ColumnReinforcement import SingleTie

rebar_group = SingleTie.editSingleTieFourRebars(
    rebar_group,                                
    l_cover_of_tie=40,        
    r_cover_of_tie=40,
    t_cover_of_tie=40,
    b_cover_of_tie=40,
    offset_of_tie=100,
    bent_angle=135,
    extension_factor=2,
    dia_of_tie=8,
    number_spacing_check=True,
    number_spacing_value=10,
    dia_of_rebars=16,
    t_offset_of_rebars=-40,
    b_offset_of_rebars=-40,
    rebar_type="LShapeRebar",
    hook_orientation="Top Outside",
    hook_extend_along="x-axis",
    l_rebar_rounding=2,
    hook_extension=40,
    structure=None,
    facename=None,
)

Edition of Single Tie Multiple Rebars

You can change the properties of the ties and rebars with the following function:

rebar_group = editSingleTieMultipleRebars(
    rebar_group,
    l_cover_of_tie,      
    r_cover_of_tie,       
    t_cover_of_tie,                       
    b_cover_of_tie,                       
    offset_of_tie,                        
    bent_angle,
    extension_factor,
    dia_of_tie,
    number_spacing_check,
    number_spacing_value,
    dia_of_main_rebars,
    main_rebars_t_offset,
    main_rebars_b_offset,
    main_rebars_type="StraightRebar",
    main_hook_orientation="Top Inside",
    main_hook_extend_along="x-axis",
    l_main_rebar_rounding=None,
    main_hook_extension=None,
    sec_rebars_t_offset=None,
    sec_rebars_b_offset=None,
    sec_rebars_number_diameter=None,
    sec_rebars_type=("StraightRebar", "StraightRebar"),
    sec_hook_orientation=("Top Inside", "Top Inside"),
    l_sec_rebar_rounding=None,
    sec_hook_extension=None,
    structure=None,
    facename=None,
)

• rebar_group is a previously created ColumnReinforcement group object.
• The other parameters are the same as required by the makeSingleTieMultipleRebars() function.
• structure and facename may be omitted so that the reinforcement stays in the original structure.

Exemplo

from ColumnReinforcement import SingleTieMultipleRebars

rebar_group = SingleTieMultipleRebars.editSingleTieMultipleRebars(
    rebar_group,                                
    l_cover_of_tie=40,        
    r_cover_of_tie=40,
    t_cover_of_tie=40,
    b_cover_of_tie=40,
    offset_of_tie=100,
    bent_angle=135,
    extension_factor=2,
    dia_of_tie=8,
    number_spacing_check=True,
    number_spacing_value=10,
    dia_of_main_rebars=16,
    main_rebars_t_offset=-40,
    main_rebars_b_offset=-40,
    main_rebars_type="LShapeRebar",
    main_hook_orientation="Top Outside",
    main_hook_extend_along="x-axis",
    l_main_rebar_rounding=2,
    main_hook_extension=40,
    sec_rebars_t_offset=(-40, -40),
    sec_rebars_b_offset=(-40, -40),
    sec_rebars_number_diameter=("2#20mm+1#16mm+2#20mm", "1#20mm+1#16mm+1#20mm"),
    sec_rebars_type=("StraightRebar", "StraightRebar"),
    sec_hook_orientation=None,
    l_sec_rebar_rounding=None,
    sec_hook_extension=None,
    structure=None,
    facename=None,
)

Armadura circular de vergalhão

Reforço de pilares com duas braçadeiras e seis barras

Arch

BIM

• 2D drafting: Sketch, Line, Polyline, Circle, Arc, Arc by 3 points, Fillet, Ellipse, Polygon, Rectangle, B-spline, Bézier curve, Cubic Bézier curve, Point

---

• 3D/BIM: Project, Site, Building, Level, Space, Wall, Curtain Wall, Column, Beam, Slab, Door, Window, Pipe, Pipe Connector, Stairs, Roof, Panel, Frame, Fence, Truss, Equipment
  • Reinforcement tools: Custom Rebar, Straight Rebar, U-Shape Rebar, L-Shape Rebar, Stirrup, Bent-Shape Rebar, Helical Rebar, Column Reinforcement, Beam Reinforcement, Slab Reinforcement, Footing Reinforcement
  • Generic 3D tools: Profile, Box, Shape builder..., Facebinder, Objects library, Component, External reference

---

• Annotation: Text, Shape from text, Aligned dimension, Horizontal dimension, Vertical dimension, Leader, Label, Axis, Axes System, Grid, Section Plane, Hatch, Page, View, Shape-based view

---

• Snapping: Snap lock, Snap endpoint, Snap midpoint, Snap center, Snap angle, Snap intersection, Snap perpendicular, Snap extension, Snap parallel, Snap special, Snap near, Snap ortho, Snap grid, Snap working plane, Snap dimensions, Toggle grid, Working Plane Top, Working Plane Front, Working Plane Side

---

• Modify: Move, Copy, Rotate, Clone, Create simple copy, Make compound, Offset, 2D Offset..., Trimex, Join, Split, Scale, Stretch, Draft to sketch, Upgrade, Downgrade, Add component, Remove component, Array, Path array, Polar array, Point array, Cut with plane, Mirror, Extrude..., Difference, Union, Intersection

---

• Manage: BIM Setup..., Views manager, Manage project..., Manage doors and windows..., Manage IFC elements..., Manage IFC quantities..., Manage IFC properties..., Manage classification..., Manage layers..., Material, Schedule, Preflight checks..., Annotation styles...

---

• Utils: Toggle bottom panels, Move to Trash, Working Plane View, Select group, Set slope, Create working plane proxy, Add to construction group, Split Mesh, Mesh to Shape, Select non-manifold meshes, Remove Shape from Arch, Close Holes, Merge Walls, Check, Toggle IFC Brep flag, Toggle subcomponents, Survey, IFC Diff, IFC explorer, Create IFC spreadsheet..., Image plane, Unclone, Rewire, Glue, Reextrude
  • Panel tools: Panel, Panel Cut, Panel Sheet, Nest
  • Structure tools: Structure, Structural System, Multiple Structures
  • IFC tools: IFC Diff..., IFC Expand, Make IFC project, IfcOpenShell update
  • Nudge: Nudge Switch, Nudge Up, Nudge Down, Nudge Left, Nudge Right, Nudge Rotate Left, Nudge Rotate Right, Nudge Extend, Nudge Shrink

---

• Additional: Preferences, Fine tuning, Import Export Preferences, IFC, DAE, OBJ, JSON, 3DS, SHP

User documentation

• Getting started
• Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
• Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate

---

• Help: Tutorials, Video tutorials
• Workbenches: Std Base, Assembly, BIM, CAM, Draft, FEM, Inspection, Material, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Surface, TechDraw, Test Framework

---

• Addons: Addon Manager, External workbenches, Scripting and macros

---

• Hubs: User hub, Power users hub, Developer hub